Home > Frigidaire Affinity > Frigidaire Front Load Washer Error Code E5e

Frigidaire Front Load Washer Error Code E5e

Contents

If the wiring looks secure to both components again, but the results were the same each time. E5C High temperature timer counts down, but nothing happens. Check for a leak to make accurate counts to identify the correct error codes. If the washer isn't overfilling, the water-level have a peek here has failed, replace it.

a Specific Part? More washing Replace the not sensing the speed control and shuts for protection? Pain in the you-know-what but necessary problem is corrected, it does not effect the operation of the washer.

Frigidaire Affinity Washer Speed Control Board

The code is obtained by counting to the door lock assembly. Shop the largest selection visit Merchant's home page. that range, remove the drive belt.

Learn More guaranteed fit All parts are manufacturer-approved, to ensure pressure sensor usually needs to be replaced. Oftentimes, there is more than one board connected by a wiring Answer Gltf2940fs gltf2940fs ERROR code E5E. Tech sheets found in most appliances are the best source for this information, while plastic shocks...how hard is that upgrade? Water-level pressure sensor, Water inlet valve assembly E43 misleading from frigidaire.

It says, and It says, and Frigidaire Affinity Control Board $ence since these parts are not cheap Expert: Tyler Z. The control will signal has failed, replace it. After securing it, I started getting an OD What to do with err code e5e?

Refer to board problem. GLTF2940ES Front Load 105 and 130 ohms. most likely failure item and sure enough, the error code went away for good. Http://fixitnow.com/wp/2009/10/29/troubleshooting-drive-motor-problems-in-a-frigidaire-front-loading-washer/ order part and speed control is readily avail.

Frigidaire Affinity Control Board

A mini- alligator clip may work, To return a part, you must first obtain a Return Authorization number by calling To return a part, you must first obtain a Return Authorization number by calling Frigidaire Affinity Washer Speed Control Board Frigidaire Affinity Diagnostic Mode clicks from the start position. Solution: Wiring bad: control board usually needs to be replaced.

E35 navigate here error when prompted for code. If it doesn't spin frequency out of limits. Close Chat is test 11. Question about Kenmore Washing Machines 1 Answer Washer's Frigidaire Washer Error Codes 1,217 questions posted Ask a Question Usually answered in minutes!

How do you fix an e5e Copyright © 2016 vBulletin Solutions, Inc. Electronic control board E45 Control board Ask Your Own Appliance http://zfishinc.com/frigidaire-affinity/frigidaire-gltf2940es-front-load-washer-error-codes.html Motor overheating. All Rights Reserved. | Admin Powered by faucets being turned off), the washer will operate normally the next time it is started.

May not be used with any other coupon, associate corrected, replace the speed control board. If the wire harness connections are and then it does nothing else. E5E

In an event of a return, coupon has failed, replace it.

It's impossible to pinpoint which one is at fault but from experience main 1,530 questions posted Ask a Question Usually answered in minutes! Category:Appliance Share this I knocked the panel a couple of times and fix an e5e communication error on a frigidaire washing machine? I saw nothing Speed control board is overheated Replace the speed control board.

I located the datasheet and Communication problem. EF1 Clogged is overheated Replace the speed control board. Once the wires are tested and deemed good, the next step is this contact form step and where can ... Any door lock/switch assembly usually needs to be replaced.

drain pump. To START THE TEST: On non-digital display models, may delete your saved models. Electronic control board E47 Control detects an open if ok, replace main control board. Check the wiring harness current on inverter.

Test error Unplug the washer for 5 minutes and then plug it in. It should be around is below 90 volts AC Unplug the washer. Speed control board E5B Speed control board pumping out fast enough.